Regardless it’s for your personal safety, for roadworthiness testing or to avoid a fine, making sure your headlamp bulbs are constantly working is very important. In reality, bulbs are wearing units that will undoubtedly burn out after some time and consequently need to be swapped out. You’re likely in this article because one of your parking lights is burnt out and you’re wondering how to change your Subaru Legacy’s license plate bulb, we’ve written this article content to help you do it on your own and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Subaru Legacy.
How to replace the license plate bulb on your Subaru Legacy coming from the outside
This technique is the least difficult of the two, in reality, for this one you will only need to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will take a moment on in the second part of this content to describe the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Subaru Legacy. Regardless it’s the front or the back of your automobile the method will be similar.
Here are a few simple steps to follow to conduct this maintenance:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this purpose (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Subaru Legacy
- Use your screwdriver or knife to remove the bulb from its placement, in the event you are afraid of breaking a thing, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the success of the operation.
.
How to replace the number plate bulb on your Subaru Legacy without outside access
Second part of our item, change this license plate bulb on your Subaru Legacy without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Subaru Legacy
To replace the one on the front plate, nothing could be much easier, you will have to put yourself under the automobile (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to apply too much pressure or you will break the plastic cover), and you will simply have to take away the burnt-out license plate bulb and replace it with the new , then test out and reassemble the whole thing.
How to replace the rear license plate bulb on my Subaru Legacy
Finally last possibility, you must replace the bulb on the backplate of your Subaru Legacy, but you cannot open the cover from the outside of your automobile. In this instance, here is the tactic to carry out this operation:
- Unplug the battery from your Subaru Legacy
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Subaru Legacy, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main solutions for replacing license plate bulbs on your car, bear in mind that on some models the method may be a bit different but you should be able to do it following the outline of this content page. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Subaru Legacy. If you want to change other bulbs like the position light bulbs on your Subaru Legacy or the low beam bulbs on Subaru Legacy, don’t hesitate to consult our content articles which describe you the process to follow.
To get more tips on the Subaru Legacy, take a look at the Subaru Legacy category.
