Regardless whether it’s for your own safety, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are in every case working is fundamental. Indeed, bulbs are wearing auto parts that will surely burn out over time and as a result need to be replaced. You’re perhaps on this website because one of your parking lights is burnt out and you’re worried about how to change your Subaru Crosstrek’s license plate bulb, we’ve created this article to help you do it by yourself and not have to go to your auto technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Subaru Crosstrek.
How to swap the license plate bulb on your Subaru Crosstrek coming from the outside
This method is the least difficult of the two, in fact, for this one you will just need to take out the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second part of this article to clarify the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Subaru Crosstrek. Regardless whether it’s the front or the back of your car the method will be similar.
Here are a few simple steps to stick to to carry out this service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this purpose (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Subaru Crosstrek
- Use your screwdriver or knife to remove the bulb from its place, in the event that you are scared of destroying something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the success of the procedure.
.
How to replace the number plate bulb on your Subaru Crosstrek without outside access
Second part of our item, change this license plate bulb on your Subaru Crosstrek without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Subaru Crosstrek
To swap the one on the front plate, nothing could be easier, you will have to position yourself under the car (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to put in too much force otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to swap the rear license plate bulb on my Subaru Crosstrek
Finally last solution, you must swap the bulb on the backplate of your Subaru Crosstrek, but you simply cannot open the cover from the outside of your car. In this instance, here is the technique to do this task:
- Unplug the battery from your Subaru Crosstrek
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Subaru Crosstrek, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main approaches for replacing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to do it following the explanation of this content page. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Subaru Crosstrek. If you wish to change other bulbs like the position light bulbs on your Subaru Crosstrek or the low beam bulbs on Subaru Crosstrek, don’t be reluctant to browse our content articles which explain you the operation to follow.
To find more tips on the Subaru Crosstrek, take a look at the Subaru Crosstrek category.
