Regardless it’s for your own personal safety, for roadworthiness testing or to avoid a fine, making sure your headlamp bulbs are all the time operational is fundamental. In reality, bulbs are wearing units that will inevitably burn out over time and as a consequence need to be changed. You’re probably on the website because one of your parking lights is burnt out and you’re wanting to know how to change your Skoda Enyaq’s license plate bulb, we’ve made this article to help you do it on your own and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Skoda Enyaq.
How to change the license plate bulb on your Skoda Enyaq coming from the outside
This method is the fastest of the two, in truth, for this one you will only require to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second part of this content page to teach you the way.
So let’s start with replacing the number plate bulb by going through the outside of your Skoda Enyaq. Regardless it’s the front or the back of your car the technique will be identical.
Here are a few simple steps to stick to to perform this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this purpose (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Skoda Enyaq
- Use your screwdriver or knife to remove the bulb from its place, in the event that you are scared of damaging anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to confirm the successfulness of the process.
.
How to replace the number plate bulb on your Skoda Enyaq without outside access
Second part of our content page, swap this license plate bulb on your Skoda Enyaq without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Skoda Enyaq
To change the one on the front plate, nothing could be less difficult, you will have to position yourself under the car (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to apply too much pressure or you will break the plastic cover), and you will simply have to take away the burnt-out license plate bulb and change it with the new , then test and reassemble the whole thing.
How to change the rear license plate bulb on my Skoda Enyaq
Finally last solution, you must change the bulb on the backplate of your Skoda Enyaq, but you cannot really open the cover from the outside of your car. In this case, here is the approach to perform this task:
- Disconnect the battery from your Skoda Enyaq
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Skoda Enyaq, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main tactics for replacing license plate bulbs on your car, take notice that on some models the technique may be a bit different but you should be able to realize it following the explanation of this content. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Skoda Enyaq. If you desire to change other bulbs like the position light bulbs on your Skoda Enyaq or the low beam bulbs on Skoda Enyaq, don’t be reluctant to read our content articles which demonstrate you the operation to follow.
If you need more tutorials on the Skoda Enyaq, go to our Skoda Enyaq category.
