Regardless it’s for your specific safety, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are in every case operational is very important. In reality, bulbs are wearing auto parts that will predictably burn out after a while and as a result need to be replaced. You’re probably here because one of your parking lights is burnt out and you’re worried about how to change your seat cordoba’s license plate bulb, we’ve made this content to help you do it without any help and not have to go to your technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your seat cordoba.
How to swap the license plate bulb on your seat cordoba throughout the outside
This solution is the least difficult of the two, actually, for this one you will just have to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second part of this article content to explain the method.
So let’s start with swapping the number plate bulb by going through the outside of your seat cordoba. Regardless it’s the front or the back of your automobile the method will be similar.
Here are a few simple steps to follow to carry out this maintenance:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this intent (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your seat cordoba
- Use your screwdriver or knife to remove the bulb from its spot, in the event that you are scared of damaging a thing, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to confirm the success of the procedure.
.
How to change the number plate bulb on your seat cordoba without outside access
Second part of our article, swap this license plate bulb on your seat cordoba without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my seat cordoba
To swap the one on the front plate, nothing could be easier, you will have to position yourself under the automobile (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally kept by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Take out the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to apply too much pressure or you will break the plastic cover), and you will simply have to remove the burnt-out license plate bulb and swap it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my seat cordoba
Finally last option, you must swap the bulb on the backplate of your seat cordoba, but you cannot open the cover from the outside of your automobile. In this case, here is the approach to do this operation:
- Unplug the battery from your seat cordoba
- Locate the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your seat cordoba, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main methods for swapping license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this article content. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your seat cordoba. If you want to change other bulbs like the position light bulbs on your seat cordoba or the low beam bulbs on seat cordoba, don’t be reluctant to read our content articles which explain you the operation to follow.
In the event that you have any additional questions about the seat cordoba, do not hesitate to consult our seat cordoba category.
