Whether it’s for your own personal security, for roadworthiness tests or to avoid a fine, ensuring your headlamp bulbs are always operational is fundamental. In fact, bulbs are wearing units that will obviously burn out after awhile and therefore need to be changed. You’re almost certainly on the website because one of your parking lights is burnt out and you’re worried about how to change your Renault Twingo 2’s license plate bulb, we’ve written and published this document to help you do it without any help and not have to go to your auto technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Renault Twingo 2.
How to replace the license plate bulb on your Renault Twingo 2 throughout the outside
This process is the most simple of the two, actually, for this one you will only have to take away the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second part of this content page to clarify the way.
So let’s start with swapping the number plate bulb by going through the outside of your Renault Twingo 2. Whether it’s the front or the back of your car the technique will be similar.
Here are a few simple actions to follow to carry out this routine service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Renault Twingo 2
- Use your screwdriver or knife to remove the bulb from its spot, in the event you are afraid of breaking something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to confirm the achievement of the procedure.
.
How to change the number plate bulb on your Renault Twingo 2 without outside access
Second part of our content, swap this license plate bulb on your Renault Twingo 2 without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Renault Twingo 2
To replace the one on the front plate, nothing could be simpler, you will have to position yourself under the car (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to put in too much pressure or you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and swap it with the new , then check and reassemble the whole thing.
How to replace the rear license plate bulb on my Renault Twingo 2
Finally last solution, you must replace the bulb on the backplate of your Renault Twingo 2, but you cannot really open the cover from the outside of your car. In such a case, here is the method to operate this task:
- Disconnect the battery from your Renault Twingo 2
- Locate the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Renault Twingo 2, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main ways for swapping license plate bulbs on your car, remember that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this article. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Renault Twingo 2. If you need to change other bulbs like the position light bulbs on your Renault Twingo 2 or the low beam bulbs on Renault Twingo 2, don’t be reluctant to consult our content articles which describe you the operation to follow.
If you need more guides on the Renault Twingo 2, go to our Renault Twingo 2 category.
