Whether it’s for your personal safety, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are in every case functioning is fundamental. Indeed, bulbs are wearing units that will obviously burn out after some time and as a consequence need to be replaced. You’re almost certainly on this site because one of your parking lights is burnt out and you’re wanting to know how to change your Renault Master 2’s license plate bulb, we’ve written this content page to help you do it without any help and not have to go to your auto technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Renault Master 2.

change-license-plate-bulb-renault-master-2

How to swap the license plate bulb on your Renault Master 2 throughout the outside

This process is the fastest of the two, in fact, for this one you will only need to take off the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate a moment on in the second section of this content page to describe the way.
So let’s start with replacing the number plate bulb by going through the outside of your Renault Master 2. Whether it’s the front or the back of your automobile the method will be the same.
Here are a few simple steps to follow to conduct this service:

  • With the engine off, disconnect the battery terminals from your car
  • Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this goal (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Renault Master 2
  • .

  • Use your screwdriver or knife to eject the bulb from its location, in the event you are afraid of damaging something, you can also do it with your fingers.
  • Finally, position the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and verify the light to confirm the achievement of the operation.

How to replace the number plate bulb on your Renault Master 2 without outside access

Second section of our content page, replace this license plate bulb on your Renault Master 2 without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).

How to swap the front license plate bulb on my Renault Master 2

To swap the one on the front plate, nothing could be simpler, you will have to position yourself under the automobile (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly kept by two soft plastic tabs by pressing on both at the same time, then once you have your license plate bulb block in hand, Take away the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much pressure otherwise you will break the plastic cover), and you will just have to take off the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.

How to swap the rear license plate bulb on my Renault Master 2

Finally last possibility, you must swap the bulb on the backplate of your Renault Master 2, but you simply cannot open the cover from the outside of your automobile. In such a case, here is the tactic to perform this operation:

  • Disconnect the battery from your Renault Master 2
  • Locate the location of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
  • Once found, before removing the bulb holders, disconnect the holders for less complicated access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Renault Master 2, verify it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have discovered the main solutions for replacing license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to realize it following the outline of this article content. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Renault Master 2. If you want to change other bulbs like the position light bulbs on your Renault Master 2 or the low beam bulbs on Renault Master 2, don’t hesitate to consult our content articles which explain you the operation to follow.

Whenever you have any additional questions about the Renault Master 2, do not hesitate to consult our Renault Master 2 category.