Regardless it’s for your own personal security, for roadworthiness tests or to avoid a fine, ensuring your headlamp bulbs are all the time functioning is very important. Indeed, bulbs are wearing units that will obviously burn out after a while and as a result need to be changed. You’re almost certainly on the website because one of your parking lights is burnt out and you’re questioning how to change your Ram ProMaster City’s license plate bulb, we’ve written and published this content page to help you do it on your own and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Ram ProMaster City.
How to replace the license plate bulb on your Ram ProMaster City coming from the outside
This solution is the easiest of the two, in reality, for this one you will simply have to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will spend a moment on in the second section of this article content to show you the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Ram ProMaster City. Regardless it’s the front or the back of your motor vehicle the operation will be the same.
Here are a few simple guidelines to follow to perform this routine service:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this intent (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ram ProMaster City
- Use your screwdriver or knife to eject the bulb from its location, in the event that you are afraid of breaking anything, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to confirm the achievement of the process.
.
How to change the number plate bulb on your Ram ProMaster City without outside access
Second section of our article, replace this license plate bulb on your Ram ProMaster City without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Ram ProMaster City
To replace the one on the front plate, nothing could be much easier, you will have to put yourself under the motor vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much force or you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Ram ProMaster City
Finally last possibility, you must replace the bulb on the backplate of your Ram ProMaster City, but you simply cannot open the cover from the outside of your motor vehicle. In such a case, here is the process to accomplish this operation:
- Unplug the battery from your Ram ProMaster City
- Locate the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Ram ProMaster City, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main tactics for swapping license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to do it following the explanation of this document. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Ram ProMaster City. If you want to change other bulbs like the position light bulbs on your Ram ProMaster City or the low beam bulbs on Ram ProMaster City, don’t be reluctant to read our content articles which explain you the procedure to follow.
To find more tips on the Ram ProMaster City, take a look at the Ram ProMaster City category.
