It doesn’t matter if it’s for your specific security, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are in every case working is really important. In reality, bulbs are wearing units that will undoubtedly burn out over time and therefore need to be replaced. You’re perhaps in this article because one of your parking lights is burnt out and you’re wondering how to change your Peugeot Rifter’s license plate bulb, we’ve created this article content to help you do it all on your own and not have to go to your mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Peugeot Rifter.
How to replace the license plate bulb on your Peugeot Rifter through the outside
This approach is the easiest of the two, in truth, for this one you will just need to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will take some time on in the second section of this document to show you the way.
So let’s start with swapping the number plate bulb by going through the outside of your Peugeot Rifter. It doesn’t matter if it’s the front or the back of your car the technique will be identical.
Here are a few simple steps to follow to perform this service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this goal (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot Rifter
- Use your screwdriver or knife to eject the bulb from its place, in the event that you are scared of breaking something, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to validate the successfulness of the operation.
.
How to replace the number plate bulb on your Peugeot Rifter without outside access
Second section of our item, swap this license plate bulb on your Peugeot Rifter without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Peugeot Rifter
To replace the one on the front plate, nothing could be less hard, you will have to position yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much pressure otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Peugeot Rifter
Finally last solution, you must replace the bulb on the backplate of your Peugeot Rifter, but you cannot open the cover from the outside of your car. In this case, here is the process to operate this operation:
- Unplug the battery from your Peugeot Rifter
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Peugeot Rifter, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main techniques for swapping license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to realize it following the outline of this content page. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Peugeot Rifter. If you wish to change other bulbs like the position light bulbs on your Peugeot Rifter or the low beam bulbs on Peugeot Rifter, don’t hesitate to browse our content articles which describe you the procedure to follow.
Whenever you have any additional questions about the Peugeot Rifter, do not hesitate to consult our Peugeot Rifter category.
