It doesn’t matter if it’s for your own personal security, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are all the time effective is fundamental. Indeed, bulbs are wearing parts that will undoubtedly burn out over time and therefore need to be changed. You’re probably on this site because one of your parking lights is burnt out and you’re struggling with how to change your Peugeot Partner Tepee’s license plate bulb, we’ve made this content to help you do it on your own and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Peugeot Partner Tepee.
How to replace the license plate bulb on your Peugeot Partner Tepee coming from the outside
This solution is the simplest of the two, in reality, for this one you will only have to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will take a moment on in the second part of this article content to show you the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Peugeot Partner Tepee. It doesn’t matter if it’s the front or the back of your car the operation will be the same.
Here are a few simple actions to stick to to perform this service:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot Partner Tepee
- Use your screwdriver or knife to remove the bulb from its location, in the event you are worried of damaging something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the success of the task.
.
How to replace the number plate bulb on your Peugeot Partner Tepee without outside access
Second part of our article, replace this license plate bulb on your Peugeot Partner Tepee without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Peugeot Partner Tepee
To replace the one on the front plate, nothing could be less complicated, you will have to position yourself under the car (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Take out the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to exert too much pressure or you will break the plastic cover), and you will simply have to take away the burnt-out license plate bulb and replace it with the new , then test out and reassemble the whole thing.
How to replace the rear license plate bulb on my Peugeot Partner Tepee
Finally last possibility, you must replace the bulb on the backplate of your Peugeot Partner Tepee, but you simply cannot open the cover from the outside of your car. In this case, here is the tactic to accomplish this task:
- Disconnect the battery from your Peugeot Partner Tepee
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Peugeot Partner Tepee, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main tactics for replacing license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to do it following the outline of this content. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Peugeot Partner Tepee. If you wish to change other bulbs like the position light bulbs on your Peugeot Partner Tepee or the low beam bulbs on Peugeot Partner Tepee, don’t hesitate to read our articles which explain you the process to follow.
To get more tips on the Peugeot Partner Tepee, take a look at the Peugeot Partner Tepee category.
