Regardless it’s for your specific safety, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are always operational is extremely important. In reality, bulbs are wearing units that will inevitably burn out over the years and therefore need to be swapped out. You’re most certainly on this website because one of your parking lights is burnt out and you’re questioning how to change your Peugeot Boxer 2’s license plate bulb, we’ve made this content page to help you do it on your own and not have to go to your technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Peugeot Boxer 2.
How to swap the license plate bulb on your Peugeot Boxer 2 throughout the outside
This option is the fastest of the two, in fact, for this one you will only require to take away the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second part of this document to clarify the approach.
So let’s begin with replacing the number plate bulb by going through the outside of your Peugeot Boxer 2. Regardless it’s the front or the back of your vehicle the method will be identical.
Here are a few simple guidelines to stick to to execute this maintenance:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this intent (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot Boxer 2
- Use your screwdriver or knife to eject the bulb from its placement, in the event that you are worried of destroying anything, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the achievement of the process.
.
How to replace the number plate bulb on your Peugeot Boxer 2 without outside access
Second part of our item, swap this license plate bulb on your Peugeot Boxer 2 without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Peugeot Boxer 2
To swap the one on the front plate, nothing could be easier, you will have to put yourself under the vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to exert too much pressure otherwise you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and swap it with the new , then test and reassemble the whole thing.
How to swap the rear license plate bulb on my Peugeot Boxer 2
Finally last option, you must swap the bulb on the backplate of your Peugeot Boxer 2, but you are not able to open the cover from the outside of your vehicle. In such a case, here is the approach to execute this operation:
- Unplug the battery from your Peugeot Boxer 2
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Peugeot Boxer 2, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main approaches for replacing license plate bulbs on your car, remember that on some models the methodology may be a bit different but you should be able to accomplish it following the explanation of this article. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Peugeot Boxer 2. If you desire to change other bulbs like the position light bulbs on your Peugeot Boxer 2 or the low beam bulbs on Peugeot Boxer 2, don’t be reluctant to browse our articles which explain you the operation to follow.
To find more tips on the Peugeot Boxer 2, take a look at the Peugeot Boxer 2 category.
