It doesn’t matter if it’s for your own safety, for roadworthiness tests or to avoid a fine, ensuring your headlamp bulbs are in every case working is extremely important. Indeed, bulbs are wearing auto parts that will obviously burn out after some time and consequently need to be changed. You’re perhaps on the website because one of your parking lights is burnt out and you’re wondering how to change your Peugeot 306’s license plate bulb, we’ve written and published this content page to help you do it on your own and not have to go to your motor mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Peugeot 306.
How to swap the license plate bulb on your Peugeot 306 throughout the outside
This option is the quickest of the two, actually, for this one you will just require to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second part of this document to clarify the method.
So let’s begin with changing the number plate bulb by going through the outside of your Peugeot 306. It doesn’t matter if it’s the front or the back of your vehicle the method will be similar.
Here are a few simple steps to follow to perform this routine service:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this goal (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot 306
- Use your screwdriver or knife to eject the bulb from its place, in the event that you are scared of damaging something, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to confirm the achievement of the procedure.
.
How to replace the number plate bulb on your Peugeot 306 without outside access
Second part of our content page, replace this license plate bulb on your Peugeot 306 without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Peugeot 306
To swap the one on the front plate, nothing could be less hard, you will have to put yourself under the vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take out the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to exert too much pressure or you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my Peugeot 306
Finally last solution, you must swap the bulb on the backplate of your Peugeot 306, but you cannot open the cover from the outside of your vehicle. In this instance, here is the method to perform this operation:
- Disconnect the battery from your Peugeot 306
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Peugeot 306, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main tactics for changing license plate bulbs on your car, remember that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this article. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Peugeot 306. If you want to change other bulbs like the position light bulbs on your Peugeot 306 or the low beam bulbs on Peugeot 306, don’t be reluctant to browse our content articles which explain you the operation to follow.
To get more tips on the Peugeot 306, take a look at the Peugeot 306 category.
