Regardless whether it’s for your own personal security, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are in every case functioning is necessary. In fact, bulbs are wearing auto parts that will predictably burn out in the future and consequently need to be replaced. You’re most likely on this website because one of your parking lights is burnt out and you’re wondering how to change your Peugeot 3008’s license plate bulb, we’ve written and published this article content to help you do it all on your own and not have to go to your technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Peugeot 3008.
How to replace the license plate bulb on your Peugeot 3008 coming from the outside
This option is the quickest of the two, in truth, for this one you will only have to take off the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second part of this document to demonstrate the method.
So let’s start with changing the number plate bulb by going through the outside of your Peugeot 3008. Regardless whether it’s the front or the back of your motor vehicle the procedure will be similar.
Here are a few simple steps to follow to perform this routine service:
- With the engine off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot 3008
- Use your screwdriver or knife to eject the bulb from its location, in the event that you are afraid of damaging something, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the success of the task.
.
How to change the number plate bulb on your Peugeot 3008 without outside access
Second part of our item, swap this license plate bulb on your Peugeot 3008 without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Peugeot 3008
To replace the one on the front plate, nothing could be simpler, you will have to put yourself under the motor vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to exert too much force otherwise you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Peugeot 3008
Finally last option, you must replace the bulb on the backplate of your Peugeot 3008, but you cannot open the cover from the outside of your motor vehicle. In this case, here is the approach to do this task:
- Unplug the battery from your Peugeot 3008
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Peugeot 3008, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main solutions for changing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to do it following the outline of this article. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Peugeot 3008. If you need to change other bulbs like the position light bulbs on your Peugeot 3008 or the low beam bulbs on Peugeot 3008, don’t be reluctant to browse our articles which explain you the operation to follow.
To discover more tips on the Peugeot 3008, take a look at the Peugeot 3008 category.
