Whether it’s for your own security, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are in every case effective is fundamental. In reality, bulbs are wearing units that will surely burn out after a while and as a consequence need to be changed. You’re probably in this article because one of your parking lights is burnt out and you’re questioning how to change your Peugeot 206 ‘s license plate bulb, we’ve made this content to help you do it all on your own and not have to go to your mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Peugeot 206 .

change-license-plate-bulb-peugeot-206-

How to change the license plate bulb on your Peugeot 206 through the outside

This tactic is the most simple of the two, in reality, for this one you will simply have to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will take some time on in the second part of this document to describe the approach.
So let’s begin with replacing the number plate bulb by going through the outside of your Peugeot 206 . Whether it’s the front or the back of your car the process will be similar.
Here are a few simple steps to follow to perform this routine service:

  • With the engine turned off, disconnect the battery terminals from your car
  • Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot 206
  • .

  • Use your screwdriver or knife to eject the bulb from its place, in the event you are afraid of destroying anything, you can also do it with your fingers.
  • Finally, position the new license plate light bulb
  • Last step, before reassembling, reconnect your battery and verify the light to confirm the achievement of the task.

How to change the number plate bulb on your Peugeot 206 without outside access

Second part of our content page, swap this license plate bulb on your Peugeot 206 without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).

How to change the front license plate bulb on my Peugeot 206

To change the one on the front plate, nothing could be less hard, you will have to position yourself under the car (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both simultaneously, then now that you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to apply too much pressure or you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.

How to change the rear license plate bulb on my Peugeot 206

Finally last solution, you must change the bulb on the backplate of your Peugeot 206 , but you cannot open the cover from the outside of your car. In this instance, here is the process to carry out this operation:

  • Disconnect the battery from your Peugeot 206
  • Locate the position of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
  • Once found, before removing the bulb holders, disconnect the holders for easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Change the burnt-out license plate bulb on your Peugeot 206 , verify it and reassemble it, paying attention to the clips on the trunk liner

.
There you have it, you have learned the main ways for replacing license plate bulbs on your car, remember that on some models the methodology may be a bit different but you should be able to realize it following the explanation of this content page. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Peugeot 206 . If you need to change other bulbs like the position light bulbs on your Peugeot 206 or the low beam bulbs on Peugeot 206 , don’t be reluctant to consult our articles which demonstrate you the procedure to follow.

If you have any further questions about the Peugeot 206 , do not hesitate to consult our Peugeot 206 category.