Whether it’s for your own security, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are all the time functional is fundamental. Indeed, bulbs are wearing auto parts that will surely burn out over the years and consequently need to be replaced. You’re most likely on the website because one of your parking lights is burnt out and you’re struggling with how to change your Peugeot 106’s license plate bulb, we’ve written this article to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Peugeot 106.
How to swap the license plate bulb on your Peugeot 106 coming from the outside
This method is the quickest of the two, in truth, for this one you will only require to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second part of this content page to show you the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Peugeot 106. Whether it’s the front or the back of your vehicle the technique will be the same.
Here are a few simple actions to stick to to perform this routine service:
- With the engine turned off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this purpose (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot 106
- Use your screwdriver or knife to remove the bulb from its location, in the event that you are worried of damaging a thing, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to validate the successfulness of the operation.
.
How to change the number plate bulb on your Peugeot 106 without outside access
Second part of our content, replace this license plate bulb on your Peugeot 106 without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Peugeot 106
To swap the one on the front plate, nothing could be less hard, you will have to position yourself under the vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally kept by two soft plastic tabs by pressing on both simultaneously, then now that you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to put in too much force or you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to swap the rear license plate bulb on my Peugeot 106
Finally last solution, you must swap the bulb on the backplate of your Peugeot 106, but you cannot open the cover from the outside of your vehicle. In this case, here is the solution to perform this task:
- Unplug the battery from your Peugeot 106
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Peugeot 106, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main approaches for replacing license plate bulbs on your car, take note that on some models the method may be a bit different but you should be able to do it following the outline of this content page. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Peugeot 106. If you desire to change other bulbs like the position light bulbs on your Peugeot 106 or the low beam bulbs on Peugeot 106, don’t be reluctant to browse our content articles which describe you the process to follow.
If you want more tutorials on the Peugeot 106, go to our Peugeot 106 category.
