Whether it’s for your own safety, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are constantly effective is really important. Indeed, bulbs are wearing parts that will undoubtedly burn out in the future and as a consequence need to be replaced. You’re likely on this site because one of your parking lights is burnt out and you’re wondering how to change your Nissan Rogue’s license plate bulb, we’ve made this content to help you do it without any help and not have to go to your auto mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Nissan Rogue.

change-license-plate-bulb-nissan-rogue

How to change the license plate bulb on your Nissan Rogue through the outside

This process is the simplest of the two, in fact, for this one you will just require to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate a moment on in the second part of this article content to demonstrate the approach.
So let’s begin with changing the number plate bulb by going through the outside of your Nissan Rogue. Whether it’s the front or the back of your car the procedure will be similar.
Here are a few simple steps to stick to to perform this routine service:

  • With the engine off, disconnect the battery terminals from your car
  • Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Nissan Rogue
  • .

  • Use your screwdriver or knife to remove the bulb from its spot, in the event you are scared of damaging anything, you can also do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and test the light to validate the success of the task.

How to replace the number plate bulb on your Nissan Rogue without outside access

Second part of our content, replace this license plate bulb on your Nissan Rogue without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).

How to change the front license plate bulb on my Nissan Rogue

To change the one on the front plate, nothing could be less complicated, you will have to put yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to apply too much force or you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and swap it with the new , then test and reassemble the whole thing.

How to change the rear license plate bulb on my Nissan Rogue

Finally last solution, you must change the bulb on the backplate of your Nissan Rogue, but you are not able to open the cover from the outside of your car. In such a case, here is the technique to execute this operation:

  • Disconnect the battery from your Nissan Rogue
  • Locate the location of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
  • Once located, before removing the bulb holders, disconnect the holders for easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Nissan Rogue, test it and reassemble it, paying attention to the clips on the trunk liner

.
There you have it, you have learned the main solutions for changing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to do it following the explanation of this content page. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Nissan Rogue. If you desire to change other bulbs like the position light bulbs on your Nissan Rogue or the low beam bulbs on Nissan Rogue, don’t be reluctant to read our content articles which explain you the procedure to follow.

To get more tips on the Nissan Rogue, take a look at the Nissan Rogue category.