It doesn’t matter if it’s for your own personal security, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are constantly functional is necessary. Indeed, bulbs are wearing auto parts that will obviously burn out in the future and consequently need to be changed. You’re perhaps in this article because one of your parking lights is burnt out and you’re worried about how to change your Nissan Micra 2’s license plate bulb, we’ve written and published this article to help you do it by yourself and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Nissan Micra 2.
How to swap the license plate bulb on your Nissan Micra 2 throughout the outside
This method is the most simple of the two, in fact, for this one you will simply require to take off the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second part of this article to clarify the method.
So let’s start with swapping the number plate bulb by going through the outside of your Nissan Micra 2. It doesn’t matter if it’s the front or the back of your vehicle the operation will be the same.
Here are a few simple guidelines to stick to to perform this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Nissan Micra 2
- Use your screwdriver or knife to remove the bulb from its location, in the event that you are worried of damaging a thing, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to confirm the achievement of the procedure.
.
How to change the number plate bulb on your Nissan Micra 2 without outside access
Second part of our content page, swap this license plate bulb on your Nissan Micra 2 without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Nissan Micra 2
To swap the one on the front plate, nothing could be less difficult, you will have to position yourself under the vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take away the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to exert too much pressure otherwise you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.
How to swap the rear license plate bulb on my Nissan Micra 2
Finally last possibility, you must swap the bulb on the backplate of your Nissan Micra 2, but you simply cannot open the cover from the outside of your vehicle. In such a case, here is the technique to accomplish this task:
- Unplug the battery from your Nissan Micra 2
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Nissan Micra 2, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main ways for swapping license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to realize it following the explanation of this article content. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Nissan Micra 2. If you want to change other bulbs like the position light bulbs on your Nissan Micra 2 or the low beam bulbs on Nissan Micra 2, don’t hesitate to consult our content articles which explain you the procedure to follow.
If perhaps you have any additional questions about the Nissan Micra 2, do not hesitate to consult our Nissan Micra 2 category.
