It doesn’t matter if it’s for your own personal security, for roadworthiness testing or to avoid a fine, being certain your headlamp bulbs are constantly working is really important. In fact, bulbs are wearing units that will undoubtedly burn out after a while and therefore need to be swapped out. You’re most likely in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Mitsubishi Space star 2’s license plate bulb, we’ve written this article content to help you do it by yourself and not have to go to your technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Mitsubishi Space star 2.
How to change the license plate bulb on your Mitsubishi Space star 2 throughout the outside
This method is the least difficult of the two, in fact, for this one you will just require to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will take a moment on in the second part of this article to teach you the way.
So let’s start with swapping the number plate bulb by going through the outside of your Mitsubishi Space star 2. It doesn’t matter if it’s the front or the back of your vehicle the method will be identical.
Here are a few simple guidelines to follow to perform this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this purpose (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mitsubishi Space star 2
- Use your screwdriver or knife to eject the bulb from its place, in the event you are worried of damaging a thing, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to confirm the success of the task.
.
How to replace the number plate bulb on your Mitsubishi Space star 2 without outside access
Second part of our item, swap this license plate bulb on your Mitsubishi Space star 2 without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Mitsubishi Space star 2
To change the one on the front plate, nothing could be less complicated, you will have to position yourself under the vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to exert too much pressure otherwise you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Mitsubishi Space star 2
Finally last option, you must change the bulb on the backplate of your Mitsubishi Space star 2, but you cannot really open the cover from the outside of your vehicle. In this case, here is the approach to conduct this operation:
- Unplug the battery from your Mitsubishi Space star 2
- Locate the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Mitsubishi Space star 2, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main ways for swapping license plate bulbs on your car, be aware that on some models the method may be a bit different but you should be able to accomplish it following the outline of this document. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Mitsubishi Space star 2. If you desire to change other bulbs like the position light bulbs on your Mitsubishi Space star 2 or the low beam bulbs on Mitsubishi Space star 2, don’t be reluctant to browse our content articles which explain you the process to follow.
To get more tips on the Mitsubishi Space star 2, take a look at the Mitsubishi Space star 2 category.
