Regardless whether it’s for your own personal safety, for roadworthiness testing or to avoid a fine, ensuring your headlamp bulbs are all the time functioning is really important. In reality, bulbs are wearing units that will obviously burn out in the future and as a consequence need to be replaced. You’re quite likely on the website because one of your parking lights is burnt out and you’re struggling with how to change your Mitsubishi Outlander’s license plate bulb, we’ve written and published this article content to help you do it without any help and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Mitsubishi Outlander.

change-license-plate-bulb-mitsubishi-outlander

How to swap the license plate bulb on your Mitsubishi Outlander through the outside

This method is the simplest of the two, in reality, for this one you will simply require to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second section of this document to describe the approach.
So let’s start with swapping the number plate bulb by going through the outside of your Mitsubishi Outlander. Regardless whether it’s the front or the back of your vehicle the procedure will be the same.
Here are a few simple actions to follow to carry out this maintenance tasks:

  • With the engine off, unplug the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this goal (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mitsubishi Outlander
  • .

  • Use your screwdriver or knife to remove the bulb from its place, if you are afraid of destroying anything, you can as well do it with your fingers.
  • Finally, position the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and check the light to validate the success of the process.

How to replace the number plate bulb on your Mitsubishi Outlander without outside access

Second section of our document, swap this license plate bulb on your Mitsubishi Outlander without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).

How to swap the front license plate bulb on my Mitsubishi Outlander

To swap the one on the front plate, nothing could be much easier, you will have to position yourself under the vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Remove the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to apply too much force otherwise you will break the plastic cover), and you will simply have to remove the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.

How to swap the rear license plate bulb on my Mitsubishi Outlander

Finally last solution, you must swap the bulb on the backplate of your Mitsubishi Outlander, but you are not able to open the cover from the outside of your vehicle. In this case, here is the process to conduct this operation:

  • Disconnect the battery from your Mitsubishi Outlander
  • Locate the location of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
  • Once established, before removing the bulb holders, unplug the holders for easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Mitsubishi Outlander, check it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have discovered the main ways for swapping license plate bulbs on your car, take notice that on some models the method may be a bit different but you should be able to realize it following the outline of this document. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Mitsubishi Outlander. If you wish to change other bulbs like the position light bulbs on your Mitsubishi Outlander or the low beam bulbs on Mitsubishi Outlander, don’t hesitate to consult our content articles which demonstrate you the procedure to follow.

Whenever you have any additional questions about the Mitsubishi Outlander, do not hesitate to consult our Mitsubishi Outlander category.