Whether it’s for your own personal security, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are in every case functioning is fundamental. In reality, bulbs are wearing parts that will undoubtedly burn out after awhile and as a consequence need to be replaced. You’re perhaps on the website because one of your parking lights is burnt out and you’re wondering how to change your Mitsubishi Lancer’s license plate bulb, we’ve written this content to help you do it without any help and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Mitsubishi Lancer.
How to change the license plate bulb on your Mitsubishi Lancer through the outside
This option is the fastest of the two, in fact, for this one you will simply need to take away the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second section of this article to teach you the way.
So let’s start with swapping the number plate bulb by going through the outside of your Mitsubishi Lancer. Whether it’s the front or the back of your motor vehicle the operation will be the same.
Here are a few simple guidelines to stick to to perform this routine service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this intent (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mitsubishi Lancer
- Use your screwdriver or knife to remove the bulb from its location, in the event you are scared of breaking anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to confirm the achievement of the operation.
.
How to change the number plate bulb on your Mitsubishi Lancer without outside access
Second section of our item, swap this license plate bulb on your Mitsubishi Lancer without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Mitsubishi Lancer
To change the one on the front plate, nothing could be less complicated, you will have to position yourself under the motor vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly held by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to exert too much force otherwise you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and change it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Mitsubishi Lancer
Finally last option, you must change the bulb on the backplate of your Mitsubishi Lancer, but you are not able to open the cover from the outside of your motor vehicle. In this instance, here is the technique to do this operation:
- Disconnect the battery from your Mitsubishi Lancer
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Mitsubishi Lancer, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main solutions for swapping license plate bulbs on your car, remember that on some models the technique may be a bit different but you should be able to realize it following the outline of this article content. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Mitsubishi Lancer. If you wish to change other bulbs like the position light bulbs on your Mitsubishi Lancer or the low beam bulbs on Mitsubishi Lancer, don’t be reluctant to read our articles which describe you the procedure to follow.
To get more tips on the Mitsubishi Lancer, take a look at the Mitsubishi Lancer category.
