It doesn’t matter if it’s for your specific safety, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are in every case working is fundamental. In reality, bulbs are wearing units that will predictably burn out after awhile and therefore need to be replaced. You’re almost certainly on this website because one of your parking lights is burnt out and you’re wondering how to change your Mercury Milan’s license plate bulb, we’ve created this document to help you do it without any help and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Mercury Milan.
How to change the license plate bulb on your Mercury Milan coming from the outside
This solution is the least difficult of the two, actually, for this one you will only have to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second section of this content page to describe the way.
So let’s start with swapping the number plate bulb by going through the outside of your Mercury Milan. It doesn’t matter if it’s the front or the back of your car the method will be similar.
Here are a few simple steps to follow to conduct this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this goal (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mercury Milan
- Use your screwdriver or knife to eject the bulb from its placement, if you are scared of breaking anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to validate the success of the process.
.
How to change the number plate bulb on your Mercury Milan without outside access
Second section of our content, swap this license plate bulb on your Mercury Milan without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Mercury Milan
To change the one on the front plate, nothing could be less complicated, you will have to position yourself under the car (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take away the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to put in too much pressure or you will break the plastic cover), and you will simply have to take away the burnt-out license plate bulb and replace it with the new , then check and reassemble the whole thing.
How to change the rear license plate bulb on my Mercury Milan
Finally last possibility, you must change the bulb on the backplate of your Mercury Milan, but you cannot open the cover from the outside of your car. In this case, here is the process to operate this operation:
- Unplug the battery from your Mercury Milan
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Mercury Milan, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main techniques for swapping license plate bulbs on your car, take note that on some models the methodology may be a bit different but you should be able to accomplish it following the outline of this article content. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Mercury Milan. If you need to change other bulbs like the position light bulbs on your Mercury Milan or the low beam bulbs on Mercury Milan, don’t be reluctant to read our content articles which describe you the operation to follow.
Whenever you have any further questions about the Mercury Milan, do not hesitate to consult our Mercury Milan category.
