Regardless whether it’s for your own security, for roadworthiness testing or to avoid a fine, being certain your headlamp bulbs are all the time working is necessary. In reality, bulbs are wearing auto parts that will predictably burn out after awhile and therefore need to be replaced. You’re perhaps here because one of your parking lights is burnt out and you’re worried about how to change your Mercedes Viano’s license plate bulb, we’ve written and published this document to help you do it without any help and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Mercedes Viano.
How to change the license plate bulb on your Mercedes Viano throughout the outside
This approach is the easiest of the two, in fact, for this one you will simply need to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second part of this content to demonstrate the approach.
So let’s begin with changing the number plate bulb by going through the outside of your Mercedes Viano. Regardless whether it’s the front or the back of your car the operation will be the same.
Here are a few simple guidelines to stick to to perform this routine service:
- With the engine off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mercedes Viano
- Use your screwdriver or knife to eject the bulb from its placement, if you are worried of breaking something, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to validate the successfulness of the task.
.
How to change the number plate bulb on your Mercedes Viano without outside access
Second part of our document, replace this license plate bulb on your Mercedes Viano without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Mercedes Viano
To change the one on the front plate, nothing could be less complicated, you will have to put yourself under the car (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to exert too much pressure or you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Mercedes Viano
Finally last solution, you must change the bulb on the backplate of your Mercedes Viano, but you simply cannot open the cover from the outside of your car. In this case, here is the approach to conduct this operation:
- Disconnect the battery from your Mercedes Viano
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Mercedes Viano, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main ways for changing license plate bulbs on your car, take note that on some models the methodology may be a bit different but you should be able to realize it following the outline of this document. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Mercedes Viano. If you desire to change other bulbs like the position light bulbs on your Mercedes Viano or the low beam bulbs on Mercedes Viano, don’t hesitate to read our content articles which describe you the process to follow.
To discover more tips on the Mercedes Viano, take a look at the Mercedes Viano category.
