Whether it’s for your own personal safety, for roadworthiness testing or to avoid a fine, making sure your headlamp bulbs are constantly functioning is fundamental. Indeed, bulbs are wearing auto parts that will predictably burn out after a while and therefore need to be replaced. You’re likely in this article because one of your parking lights is burnt out and you’re struggling with how to change your Mercedes Classe Cls’s license plate bulb, we’ve written and published this document to help you do it without any help and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Mercedes Classe Cls.
How to replace the license plate bulb on your Mercedes Classe Cls throughout the outside
This solution is the quickest of the two, actually, for this one you will simply need to remove the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second part of this article to demonstrate the way.
So let’s start with swapping the number plate bulb by going through the outside of your Mercedes Classe Cls. Whether it’s the front or the back of your vehicle the technique will be identical.
Here are a few simple steps to stick to to perform this maintenance tasks:
- With the engine off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mercedes Classe Cls
- Use your screwdriver or knife to eject the bulb from its place, in the event that you are scared of breaking anything, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to confirm the achievement of the process.
.
How to replace the number plate bulb on your Mercedes Classe Cls without outside access
Second part of our item, swap this license plate bulb on your Mercedes Classe Cls without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Mercedes Classe Cls
To replace the one on the front plate, nothing could be less difficult, you will have to put yourself under the vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much force otherwise you will break the plastic cover), and you will simply have to remove the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.
How to replace the rear license plate bulb on my Mercedes Classe Cls
Finally last possibility, you must replace the bulb on the backplate of your Mercedes Classe Cls, but you cannot open the cover from the outside of your vehicle. In such a case, here is the process to accomplish this operation:
- Unplug the battery from your Mercedes Classe Cls
- Locate the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Mercedes Classe Cls, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main ways for swapping license plate bulbs on your car, take note that on some models the methodology may be a bit different but you should be able to do it following the outline of this article. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Mercedes Classe Cls. If you want to change other bulbs like the position light bulbs on your Mercedes Classe Cls or the low beam bulbs on Mercedes Classe Cls, don’t be reluctant to browse our articles which describe you the procedure to follow.
Whenever you have any additional questions about the Mercedes Classe Cls, do not hesitate to consult our Mercedes Classe Cls category.
