Regardless whether it’s for your own safety, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are constantly functioning is fundamental. In fact, bulbs are wearing parts that will obviously burn out in the future and therefore need to be swapped out. You’re most certainly here because one of your parking lights is burnt out and you’re struggling with how to change your Mercedes Classe A 3’s license plate bulb, we’ve written and published this article content to help you do it on your own and not have to go to your technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Mercedes Classe A 3.
How to change the license plate bulb on your Mercedes Classe A 3 throughout the outside
This solution is the most simple of the two, in reality, for this one you will just need to take out the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will take some time on in the second part of this content to explain the method.
So let’s begin with changing the number plate bulb by going through the outside of your Mercedes Classe A 3. Regardless whether it’s the front or the back of your car the process will be similar.
Here are a few simple steps to stick to to conduct this maintenance:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mercedes Classe A 3
- Use your screwdriver or knife to eject the bulb from its place, in the event that you are worried of damaging anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the success of the task.
.
How to change the number plate bulb on your Mercedes Classe A 3 without outside access
Second part of our article, replace this license plate bulb on your Mercedes Classe A 3 without external access. Generally you will be able to access it, but some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Mercedes Classe A 3
To change the one on the front plate, nothing could be less complicated, you will have to position yourself under the car (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to exert too much force or you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.
How to change the rear license plate bulb on my Mercedes Classe A 3
Finally last possibility, you must change the bulb on the backplate of your Mercedes Classe A 3, but you simply cannot open the cover from the outside of your car. In this instance, here is the tactic to perform this operation:
- Unplug the battery from your Mercedes Classe A 3
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Mercedes Classe A 3, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main ways for changing license plate bulbs on your car, remember that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this content page. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Mercedes Classe A 3. If you wish to change other bulbs like the position light bulbs on your Mercedes Classe A 3 or the low beam bulbs on Mercedes Classe A 3, don’t hesitate to browse our content articles which demonstrate you the procedure to follow.
Whenever you have any additional questions about the Mercedes Classe A 3, do not hesitate to consult our Mercedes Classe A 3 category.
