Regardless whether it’s for your specific safety, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are always functional is extremely important. In reality, bulbs are wearing auto parts that will inevitably burn out as time passes and as a consequence need to be changed. You’re most certainly on the website because one of your parking lights is burnt out and you’re worried about how to change your Mazda MX 5 Miata’s license plate bulb, we’ve written and published this content page to help you do it on your own and not have to go to your motor mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Mazda MX 5 Miata.
How to change the license plate bulb on your Mazda MX 5 Miata throughout the outside
This technique is the easiest of the two, actually, for this one you will simply require to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second section of this content page to clarify the method.
So let’s begin with swapping the number plate bulb by going through the outside of your Mazda MX 5 Miata. Regardless whether it’s the front or the back of your motor vehicle the operation will be the same.
Here are a few simple steps to follow to execute this service:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this goal (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mazda MX 5 Miata
- Use your screwdriver or knife to remove the bulb from its spot, if you are worried of damaging a thing, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to validate the success of the task.
.
How to replace the number plate bulb on your Mazda MX 5 Miata without outside access
Second section of our document, swap this license plate bulb on your Mazda MX 5 Miata without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Mazda MX 5 Miata
To change the one on the front plate, nothing could be less complicated, you will have to put yourself under the motor vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally kept by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to put in too much force or you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and change it with the new , then test and reassemble the whole thing.
How to change the rear license plate bulb on my Mazda MX 5 Miata
Finally last option, you must change the bulb on the backplate of your Mazda MX 5 Miata, but you cannot really open the cover from the outside of your motor vehicle. In such a case, here is the technique to carry out this task:
- Disconnect the battery from your Mazda MX 5 Miata
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Mazda MX 5 Miata, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main approaches for swapping license plate bulbs on your car, take notice that on some models the methodology may be a bit different but you should be able to do it following the outline of this content. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Mazda MX 5 Miata. If you wish to change other bulbs like the position light bulbs on your Mazda MX 5 Miata or the low beam bulbs on Mazda MX 5 Miata, don’t hesitate to consult our articles which describe you the process to follow.
If you need more tutorials on the Mazda MX 5 Miata, go to our Mazda MX 5 Miata category.
