It doesn’t matter if it’s for your specific safety, for roadworthiness testing or to avoid a fine, being certain your headlamp bulbs are constantly functional is very important. In fact, bulbs are wearing auto parts that will inevitably burn out after a while and as a consequence need to be swapped out. You’re likely in this article because one of your parking lights is burnt out and you’re questioning how to change your Mazda 6’s license plate bulb, we’ve made this document to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Mazda 6.
How to change the license plate bulb on your Mazda 6 throughout the outside
This solution is the most simple of the two, in truth, for this one you will only need to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second section of this content page to teach you the method.
So let’s begin with swapping the number plate bulb by going through the outside of your Mazda 6. It doesn’t matter if it’s the front or the back of your motor vehicle the process will be similar.
Here are a few simple steps to follow to conduct this maintenance:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this purpose (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mazda 6
- Use your screwdriver or knife to eject the bulb from its location, in the event you are worried of damaging something, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to validate the successfulness of the operation.
.
How to change the number plate bulb on your Mazda 6 without outside access
Second section of our document, replace this license plate bulb on your Mazda 6 without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Mazda 6
To change the one on the front plate, nothing could be easier, you will have to put yourself under the motor vehicle (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally kept by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to put in too much pressure or you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and replace it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Mazda 6
Finally last option, you must change the bulb on the backplate of your Mazda 6, but you simply cannot open the cover from the outside of your motor vehicle. In such a case, here is the tactic to execute this task:
- Unplug the battery from your Mazda 6
- Locate the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Mazda 6, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main methods for swapping license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to realize it following the outline of this document. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Mazda 6. If you desire to change other bulbs like the position light bulbs on your Mazda 6 or the low beam bulbs on Mazda 6, don’t be reluctant to read our articles which describe you the procedure to follow.
To discover more tips on the Mazda 6, take a look at the Mazda 6 category.
