Regardless whether it’s for your personal safety, for roadworthiness testing or to avoid a fine, being certain your headlamp bulbs are constantly operational is extremely important. In reality, bulbs are wearing units that will obviously burn out with time and as a result need to be changed. You’re almost certainly on this site because one of your parking lights is burnt out and you’re struggling with how to change your Mazda 5’s license plate bulb, we’ve written this article content to help you do it without any help and not have to go to your technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Mazda 5.
How to change the license plate bulb on your Mazda 5 through the outside
This method is the simplest of the two, in reality, for this one you will only require to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second section of this article content to explain the method.
So let’s start with changing the number plate bulb by going through the outside of your Mazda 5. Regardless whether it’s the front or the back of your motor vehicle the technique will be the same.
Here are a few simple guidelines to stick to to perform this maintenance tasks:
- With the engine turned off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mazda 5
- Use your screwdriver or knife to eject the bulb from its place, in the event that you are worried of breaking something, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to confirm the successfulness of the process.
.
How to replace the number plate bulb on your Mazda 5 without outside access
Second section of our content, replace this license plate bulb on your Mazda 5 without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Mazda 5
To change the one on the front plate, nothing could be less difficult, you will have to put yourself under the motor vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Remove the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to exert too much force otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.
How to change the rear license plate bulb on my Mazda 5
Finally last solution, you must change the bulb on the backplate of your Mazda 5, but you cannot really open the cover from the outside of your motor vehicle. In this case, here is the technique to operate this operation:
- Disconnect the battery from your Mazda 5
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Mazda 5, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main tactics for changing license plate bulbs on your car, take note that on some models the method may be a bit different but you should be able to accomplish it following the explanation of this content page. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Mazda 5. If you wish to change other bulbs like the position light bulbs on your Mazda 5 or the low beam bulbs on Mazda 5, don’t be reluctant to read our content articles which explain you the process to follow.
If you wish more guides on the Mazda 5, go to our Mazda 5 category.
