Regardless it’s for your own personal safety, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are constantly functioning is really important. In fact, bulbs are wearing parts that will inevitably burn out after some time and therefore need to be replaced. You’re most likely on this site because one of your parking lights is burnt out and you’re questioning how to change your Mazda 2’s license plate bulb, we’ve written and published this content page to help you do it all on your own and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Mazda 2.

change-license-plate-bulb-mazda-2

How to change the license plate bulb on your Mazda 2 throughout the outside

This option is the least difficult of the two, in fact, for this one you will just have to take off the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will spend a moment on in the second part of this content page to describe the method.
So let’s start with swapping the number plate bulb by going through the outside of your Mazda 2. Regardless it’s the front or the back of your car the procedure will be the same.
Here are a few simple actions to stick to to carry out this service:

  • With the engine turned off, unplug the battery terminals from your car
  • Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this intent (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mazda 2
  • .

  • Use your screwdriver or knife to eject the bulb from its placement, in the event you are scared of breaking something, you can as well do it with your fingers.
  • Finally, position the new license plate light bulb
  • Last step, before reassembling, reconnect your battery and check the light to validate the successfulness of the task.

How to change the number plate bulb on your Mazda 2 without outside access

Second part of our article, swap this license plate bulb on your Mazda 2 without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).

How to change the front license plate bulb on my Mazda 2

To change the one on the front plate, nothing could be easier, you will have to position yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly held by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Take away the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to exert too much pressure or you will break the plastic cover), and you will simply have to take off the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.

How to change the rear license plate bulb on my Mazda 2

Finally last option, you must change the bulb on the backplate of your Mazda 2, but you are not able to open the cover from the outside of your car. In this instance, here is the approach to do this task:

  • Unplug the battery from your Mazda 2
  • Identify the position of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
  • Once located, before removing the bulb holders, unplug the holders for easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Mazda 2, check it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have learned the main approaches for swapping license plate bulbs on your car, take note that on some models the method may be a bit different but you should be able to accomplish it following the explanation of this article. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Mazda 2. If you need to change other bulbs like the position light bulbs on your Mazda 2 or the low beam bulbs on Mazda 2, don’t hesitate to read our content articles which demonstrate you the operation to follow.

To discover more tips on the Mazda 2, take a look at the Mazda 2 category.