Regardless whether it’s for your own security, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are all the time functional is really important. In reality, bulbs are wearing units that will obviously burn out after a while and as a result need to be changed. You’re quite likely on the website because one of your parking lights is burnt out and you’re wondering how to change your Lincoln MKZ’s license plate bulb, we’ve created this content to help you do it by yourself and not have to go to your auto mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Lincoln MKZ.
How to swap the license plate bulb on your Lincoln MKZ through the outside
This method is the least difficult of the two, in reality, for this one you will only have to take away the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second section of this article to describe the approach.
So let’s start with changing the number plate bulb by going through the outside of your Lincoln MKZ. Regardless whether it’s the front or the back of your vehicle the operation will be similar.
Here are a few simple actions to follow to perform this service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this purpose (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Lincoln MKZ
- Use your screwdriver or knife to eject the bulb from its location, if you are scared of damaging anything, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to confirm the achievement of the task.
.
How to change the number plate bulb on your Lincoln MKZ without outside access
Second section of our document, change this license plate bulb on your Lincoln MKZ without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Lincoln MKZ
To swap the one on the front plate, nothing could be less complicated, you will have to put yourself under the vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much force otherwise you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.
How to swap the rear license plate bulb on my Lincoln MKZ
Finally last possibility, you must swap the bulb on the backplate of your Lincoln MKZ, but you are not able to open the cover from the outside of your vehicle. In such a case, here is the technique to operate this operation:
- Unplug the battery from your Lincoln MKZ
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Lincoln MKZ, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main techniques for changing license plate bulbs on your car, remember that on some models the technique may be a bit different but you should be able to do it following the explanation of this article. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Lincoln MKZ. If you want to change other bulbs like the position light bulbs on your Lincoln MKZ or the low beam bulbs on Lincoln MKZ, don’t be reluctant to consult our content articles which describe you the operation to follow.
If perhaps you have any further questions about the Lincoln MKZ, do not hesitate to consult our Lincoln MKZ category.
