Regardless whether it’s for your personal security, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are constantly functioning is very important. Indeed, bulbs are wearing auto parts that will inevitably burn out as time passes and as a result need to be changed. You’re probably in this article because one of your parking lights is burnt out and you’re questioning how to change your Land Rover Evoque’s license plate bulb, we’ve created this content page to help you do it by yourself and not have to go to your technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Land Rover Evoque.
How to replace the license plate bulb on your Land Rover Evoque throughout the outside
This process is the least difficult of the two, actually, for this one you will only require to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second section of this article content to demonstrate the approach.
So let’s begin with swapping the number plate bulb by going through the outside of your Land Rover Evoque. Regardless whether it’s the front or the back of your car the method will be the same.
Here are a few simple actions to stick to to perform this routine service:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this intent (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Land Rover Evoque
- Use your screwdriver or knife to remove the bulb from its place, if you are afraid of destroying anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to validate the achievement of the procedure.
.
How to replace the number plate bulb on your Land Rover Evoque without outside access
Second section of our document, replace this license plate bulb on your Land Rover Evoque without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Land Rover Evoque
To replace the one on the front plate, nothing could be much easier, you will have to position yourself under the car (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually kept by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to put in too much pressure otherwise you will break the plastic cover), and you will simply have to remove the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Land Rover Evoque
Finally last solution, you must replace the bulb on the backplate of your Land Rover Evoque, but you simply cannot open the cover from the outside of your car. In this instance, here is the process to operate this operation:
- Unplug the battery from your Land Rover Evoque
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Land Rover Evoque, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main techniques for swapping license plate bulbs on your car, take note that on some models the method may be a bit different but you should be able to accomplish it following the outline of this article content. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Land Rover Evoque. If you desire to change other bulbs like the position light bulbs on your Land Rover Evoque or the low beam bulbs on Land Rover Evoque, don’t hesitate to consult our content articles which explain you the procedure to follow.
If you want more guides on the Land Rover Evoque, go to our Land Rover Evoque category.
