Regardless whether it’s for your own safety, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are in every case functional is necessary. In fact, bulbs are wearing units that will undoubtedly burn out after some time and consequently need to be replaced. You’re most certainly on this website because one of your parking lights is burnt out and you’re wondering how to change your Land Rover Discovery’s license plate bulb, we’ve written and published this content page to help you do it on your own and not have to go to your mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Land Rover Discovery.
How to change the license plate bulb on your Land Rover Discovery throughout the outside
This solution is the quickest of the two, in fact, for this one you will just require to remove the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will take some time on in the second part of this article to teach you the approach.
So let’s start with swapping the number plate bulb by going through the outside of your Land Rover Discovery. Regardless whether it’s the front or the back of your vehicle the method will be similar.
Here are a few simple steps to follow to conduct this service:
- With the engine off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this intent (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Land Rover Discovery
- Use your screwdriver or knife to remove the bulb from its placement, in the event that you are scared of destroying anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to confirm the success of the process.
.
How to change the number plate bulb on your Land Rover Discovery without outside access
Second part of our article, change this license plate bulb on your Land Rover Discovery without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Land Rover Discovery
To change the one on the front plate, nothing could be easier, you will have to position yourself under the vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly kept by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to apply too much force or you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Land Rover Discovery
Finally last option, you must change the bulb on the backplate of your Land Rover Discovery, but you cannot really open the cover from the outside of your vehicle. In this instance, here is the process to accomplish this task:
- Unplug the battery from your Land Rover Discovery
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Land Rover Discovery, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main solutions for swapping license plate bulbs on your car, remember that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this article content. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Land Rover Discovery. If you need to change other bulbs like the position light bulbs on your Land Rover Discovery or the low beam bulbs on Land Rover Discovery, don’t be reluctant to read our content articles which demonstrate you the operation to follow.
To get more tips on the Land Rover Discovery, take a look at the Land Rover Discovery category.
