Regardless it’s for your own security, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are all the time functioning is very important. In fact, bulbs are wearing parts that will predictably burn out over time and therefore need to be changed. You’re quite likely in this article because one of your parking lights is burnt out and you’re wondering how to change your Land Rover Defender’s license plate bulb, we’ve written this article to help you do it by yourself and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Land Rover Defender.

change-license-plate-bulb-land-rover-defender

How to swap the license plate bulb on your Land Rover Defender through the outside

This process is the most simple of the two, in reality, for this one you will simply require to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will spend a moment on in the second section of this article content to demonstrate the method.
So let’s begin with swapping the number plate bulb by going through the outside of your Land Rover Defender. Regardless it’s the front or the back of your car the operation will be the same.
Here are a few simple guidelines to stick to to carry out this routine service:

  • With the engine off, unplug the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this purpose (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Land Rover Defender
  • .

  • Use your screwdriver or knife to remove the bulb from its place, in the event that you are worried of destroying a thing, you can also do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last step, before reassembling, reconnect your battery and check the light to confirm the success of the process.

How to change the number plate bulb on your Land Rover Defender without outside access

Second section of our content, change this license plate bulb on your Land Rover Defender without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).

How to swap the front license plate bulb on my Land Rover Defender

To swap the one on the front plate, nothing could be simpler, you will have to put yourself under the car (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally kept by two soft plastic tabs by pressing on both at the same time, then once you have your license plate bulb block in hand, Take away the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to exert too much force otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and change it with the new , then test out and reassemble the whole thing.

How to swap the rear license plate bulb on my Land Rover Defender

Finally last solution, you must swap the bulb on the backplate of your Land Rover Defender, but you are not able to open the cover from the outside of your car. In this instance, here is the method to carry out this task:

  • Disconnect the battery from your Land Rover Defender
  • Locate the spot of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
  • Once found, before removing the bulb holders, unplug the holders for less difficult access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Land Rover Defender, check it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have learned the main solutions for swapping license plate bulbs on your car, bear in mind that on some models the methodology may be a bit different but you should be able to do it following the explanation of this content. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Land Rover Defender. If you wish to change other bulbs like the position light bulbs on your Land Rover Defender or the low beam bulbs on Land Rover Defender, don’t hesitate to browse our articles which explain you the process to follow.

To discover more tips on the Land Rover Defender, take a look at the Land Rover Defender category.