Regardless it’s for your own safety, for roadworthiness tests or to avoid a fine, ensuring your headlamp bulbs are in every case functional is fundamental. Indeed, bulbs are wearing units that will obviously burn out after awhile and as a result need to be replaced. You’re perhaps in this article because one of your parking lights is burnt out and you’re struggling with how to change your Kia Picanto’s license plate bulb, we’ve written this article to help you do it by yourself and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Kia Picanto.
How to change the license plate bulb on your Kia Picanto throughout the outside
This solution is the most simple of the two, in truth, for this one you will simply need to take off the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second part of this document to clarify the approach.
So let’s start with changing the number plate bulb by going through the outside of your Kia Picanto. Regardless it’s the front or the back of your automobile the operation will be similar.
Here are a few simple guidelines to follow to conduct this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Kia Picanto
- Use your screwdriver or knife to eject the bulb from its spot, if you are scared of damaging a thing, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the successfulness of the procedure.
.
How to replace the number plate bulb on your Kia Picanto without outside access
Second part of our document, change this license plate bulb on your Kia Picanto without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Kia Picanto
To change the one on the front plate, nothing could be much easier, you will have to position yourself under the automobile (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to apply too much pressure or you will break the plastic cover), and you will simply have to take off the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Kia Picanto
Finally last possibility, you must change the bulb on the backplate of your Kia Picanto, but you simply cannot open the cover from the outside of your automobile. In such a case, here is the process to carry out this task:
- Disconnect the battery from your Kia Picanto
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Kia Picanto, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main techniques for changing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to accomplish it following the outline of this content. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Kia Picanto. If you need to change other bulbs like the position light bulbs on your Kia Picanto or the low beam bulbs on Kia Picanto, don’t hesitate to browse our content articles which describe you the procedure to follow.
Whenever you have any further questions about the Kia Picanto, do not hesitate to consult our Kia Picanto category.
