Regardless it’s for your own personal safety, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are always operational is really important. In fact, bulbs are wearing auto parts that will predictably burn out over the years and consequently need to be swapped out. You’re likely on this website because one of your parking lights is burnt out and you’re wanting to know how to change your Jeep Wrangler’s license plate bulb, we’ve written and published this article content to help you do it on your own and not have to go to your auto technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Jeep Wrangler.
How to change the license plate bulb on your Jeep Wrangler through the outside
This method is the most simple of the two, in truth, for this one you will only have to remove the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second part of this content to clarify the approach.
So let’s start with changing the number plate bulb by going through the outside of your Jeep Wrangler. Regardless it’s the front or the back of your car the procedure will be the same.
Here are a few simple actions to follow to carry out this service:
- With the engine off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this purpose (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Jeep Wrangler
- Use your screwdriver or knife to remove the bulb from its location, in the event you are scared of destroying something, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to confirm the success of the procedure.
.
How to change the number plate bulb on your Jeep Wrangler without outside access
Second part of our item, swap this license plate bulb on your Jeep Wrangler without external access. Generally you will be able to access it, but some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Jeep Wrangler
To change the one on the front plate, nothing could be less complicated, you will have to put yourself under the car (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both simultaneously, then now that you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to apply too much pressure otherwise you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and change it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Jeep Wrangler
Finally last option, you must change the bulb on the backplate of your Jeep Wrangler, but you cannot really open the cover from the outside of your car. In such a case, here is the process to execute this operation:
- Unplug the battery from your Jeep Wrangler
- Locate the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Jeep Wrangler, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main tactics for changing license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to accomplish it following the explanation of this document. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Jeep Wrangler. If you wish to change other bulbs like the position light bulbs on your Jeep Wrangler or the low beam bulbs on Jeep Wrangler, don’t hesitate to read our articles which describe you the operation to follow.
To find more tips on the Jeep Wrangler, take a look at the Jeep Wrangler category.
