It doesn’t matter if it’s for your specific security, for roadworthiness testing or to avoid a fine, ensuring your headlamp bulbs are always functioning is very important. Indeed, bulbs are wearing units that will inevitably burn out over the years and as a result need to be changed. You’re perhaps on the website because one of your parking lights is burnt out and you’re wondering how to change your Jeep Grand Cherokee’s license plate bulb, we’ve made this article to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Jeep Grand Cherokee.
How to replace the license plate bulb on your Jeep Grand Cherokee through the outside
This option is the simplest of the two, actually, for this one you will only have to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second part of this document to clarify the way.
So let’s begin with replacing the number plate bulb by going through the outside of your Jeep Grand Cherokee. It doesn’t matter if it’s the front or the back of your vehicle the operation will be identical.
Here are a few simple steps to stick to to execute this maintenance:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Jeep Grand Cherokee
- Use your screwdriver or knife to eject the bulb from its placement, in the event you are afraid of damaging a thing, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to confirm the successfulness of the task.
.
How to change the number plate bulb on your Jeep Grand Cherokee without outside access
Second part of our article, replace this license plate bulb on your Jeep Grand Cherokee without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Jeep Grand Cherokee
To replace the one on the front plate, nothing could be less complicated, you will have to put yourself under the vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to exert too much force otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and replace it with the new , then check and reassemble the whole thing.
How to replace the rear license plate bulb on my Jeep Grand Cherokee
Finally last possibility, you must replace the bulb on the backplate of your Jeep Grand Cherokee, but you are not able to open the cover from the outside of your vehicle. In this case, here is the method to execute this task:
- Disconnect the battery from your Jeep Grand Cherokee
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Jeep Grand Cherokee, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main methods for replacing license plate bulbs on your car, take notice that on some models the methodology may be a bit different but you should be able to do it following the explanation of this document. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Jeep Grand Cherokee. If you desire to change other bulbs like the position light bulbs on your Jeep Grand Cherokee or the low beam bulbs on Jeep Grand Cherokee, don’t hesitate to consult our articles which demonstrate you the process to follow.
To get more tips on the Jeep Grand Cherokee, take a look at the Jeep Grand Cherokee category.
