Regardless whether it’s for your own safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are all the time functional is fundamental. Indeed, bulbs are wearing units that will inevitably burn out after a while and therefore need to be replaced. You’re probably here because one of your parking lights is burnt out and you’re worried about how to change your Jeep Gladiator’s license plate bulb, we’ve created this article to help you do it without any help and not have to go to your auto mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Jeep Gladiator.
How to replace the license plate bulb on your Jeep Gladiator coming from the outside
This technique is the most simple of the two, in truth, for this one you will simply have to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate a moment on in the second part of this content to teach you the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Jeep Gladiator. Regardless whether it’s the front or the back of your automobile the process will be similar.
Here are a few simple steps to follow to carry out this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Jeep Gladiator
- Use your screwdriver or knife to remove the bulb from its place, in the event you are afraid of damaging something, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the success of the procedure.
.
How to change the number plate bulb on your Jeep Gladiator without outside access
Second part of our content, swap this license plate bulb on your Jeep Gladiator without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Jeep Gladiator
To replace the one on the front plate, nothing could be less hard, you will have to put yourself under the automobile (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much pressure otherwise you will break the plastic cover), and you will only have to take out the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to replace the rear license plate bulb on my Jeep Gladiator
Finally last solution, you must replace the bulb on the backplate of your Jeep Gladiator, but you cannot really open the cover from the outside of your automobile. In this case, here is the approach to carry out this operation:
- Unplug the battery from your Jeep Gladiator
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Jeep Gladiator, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main methods for swapping license plate bulbs on your car, take notice that on some models the method may be a bit different but you should be able to accomplish it following the outline of this article. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Jeep Gladiator. If you need to change other bulbs like the position light bulbs on your Jeep Gladiator or the low beam bulbs on Jeep Gladiator, don’t hesitate to browse our content articles which demonstrate you the procedure to follow.
If perhaps you have any further questions about the Jeep Gladiator, do not hesitate to consult our Jeep Gladiator category.
