It doesn’t matter if it’s for your specific security, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are all the time functioning is fundamental. In reality, bulbs are wearing parts that will obviously burn out after a while and consequently need to be swapped out. You’re almost certainly in this article because one of your parking lights is burnt out and you’re questioning how to change your Infiniti QX30’s license plate bulb, we’ve written this content page to help you do it by yourself and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Infiniti QX30.
How to replace the license plate bulb on your Infiniti QX30 through the outside
This method is the simplest of the two, in reality, for this one you will simply require to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate a moment on in the second section of this article content to describe the method.
So let’s start with changing the number plate bulb by going through the outside of your Infiniti QX30. It doesn’t matter if it’s the front or the back of your vehicle the method will be similar.
Here are a few simple actions to stick to to carry out this routine service:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Infiniti QX30
- Use your screwdriver or knife to remove the bulb from its placement, in the event you are afraid of destroying a thing, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the successfulness of the procedure.
.
How to change the number plate bulb on your Infiniti QX30 without outside access
Second section of our content page, swap this license plate bulb on your Infiniti QX30 without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Infiniti QX30
To replace the one on the front plate, nothing could be simpler, you will have to position yourself under the vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to put in too much force or you will break the plastic cover), and you will just have to take off the burnt-out license plate bulb and replace it with the new , then test out and reassemble the whole thing.
How to replace the rear license plate bulb on my Infiniti QX30
Finally last option, you must replace the bulb on the backplate of your Infiniti QX30, but you are not able to open the cover from the outside of your vehicle. In such a case, here is the solution to carry out this operation:
- Unplug the battery from your Infiniti QX30
- Locate the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Infiniti QX30, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main methods for changing license plate bulbs on your car, take note that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this content page. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Infiniti QX30. If you desire to change other bulbs like the position light bulbs on your Infiniti QX30 or the low beam bulbs on Infiniti QX30, don’t hesitate to consult our articles which demonstrate you the operation to follow.
If you need more guides on the Infiniti QX30, go to our Infiniti QX30 category.
