Regardless it’s for your specific safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are always effective is really important. Indeed, bulbs are wearing units that will undoubtedly burn out with time and therefore need to be swapped out. You’re likely in this article because one of your parking lights is burnt out and you’re questioning how to change your Hyundai Santa Fe’s license plate bulb, we’ve made this document to help you do it without any help and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Hyundai Santa Fe.

change-license-plate-bulb-hyundai-santa-fe

How to replace the license plate bulb on your Hyundai Santa Fe coming from the outside

This technique is the most simple of the two, actually, for this one you will just require to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will take some time on in the second section of this article to teach you the approach.
So let’s begin with replacing the number plate bulb by going through the outside of your Hyundai Santa Fe. Regardless it’s the front or the back of your automobile the operation will be similar.
Here are a few simple steps to stick to to execute this routine service:

  • With the engine turned off, unplug the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this intent (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Hyundai Santa Fe
  • .

  • Use your screwdriver or knife to remove the bulb from its place, in the event that you are scared of damaging anything, you can as well do it with your fingers.
  • Finally, position the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and check the light to validate the successfulness of the task.

How to replace the number plate bulb on your Hyundai Santa Fe without outside access

Second section of our content page, change this license plate bulb on your Hyundai Santa Fe without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).

How to replace the front license plate bulb on my Hyundai Santa Fe

To replace the one on the front plate, nothing could be less complicated, you will have to position yourself under the automobile (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly held by two soft plastic tabs by pressing on both simultaneously, then now that you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to exert too much pressure otherwise you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.

How to replace the rear license plate bulb on my Hyundai Santa Fe

Finally last possibility, you must replace the bulb on the backplate of your Hyundai Santa Fe, but you simply cannot open the cover from the outside of your automobile. In such a case, here is the tactic to carry out this task:

  • Unplug the battery from your Hyundai Santa Fe
  • Find the spot of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
  • Once found, before removing the bulb holders, unplug the holders for less difficult access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Hyundai Santa Fe, check it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have discovered the main solutions for replacing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to accomplish it following the outline of this article. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Hyundai Santa Fe. If you desire to change other bulbs like the position light bulbs on your Hyundai Santa Fe or the low beam bulbs on Hyundai Santa Fe, don’t be reluctant to read our articles which demonstrate you the operation to follow.

To get more tips on the Hyundai Santa Fe, take a look at the Hyundai Santa Fe category.