It doesn’t matter if it’s for your own safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are in every case effective is extremely important. In fact, bulbs are wearing units that will obviously burn out after some time and therefore need to be swapped out. You’re most certainly here because one of your parking lights is burnt out and you’re struggling with how to change your hyundai i20’s license plate bulb, we’ve written and published this document to help you do it without any help and not have to go to your auto technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your hyundai i20.

change-license-plate-bulb-hyundai-i20

How to replace the license plate bulb on your hyundai i20 through the outside

This approach is the easiest of the two, in fact, for this one you will simply need to take off the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will spend a moment on in the second section of this content page to show you the way.
So let’s begin with replacing the number plate bulb by going through the outside of your hyundai i20. It doesn’t matter if it’s the front or the back of your automobile the process will be the same.
Here are a few simple guidelines to follow to execute this service:

  • With the engine turned off, unplug the battery terminals from your car
  • Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your hyundai i20
  • .

  • Use your screwdriver or knife to remove the bulb from its spot, in the event that you are worried of damaging anything, you can as well do it with your fingers.
  • Finally, position the new license plate light bulb
  • Last step, before reassembling, reconnect your battery and test the light to validate the achievement of the procedure.

How to change the number plate bulb on your hyundai i20 without outside access

Second section of our article, change this license plate bulb on your hyundai i20 without external access. Generally you will be able to access it, but some series (often at the rear does not allow this access).

How to replace the front license plate bulb on my hyundai i20

To replace the one on the front plate, nothing could be easier, you will have to position yourself under the automobile (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much pressure otherwise you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and replace it with the new , then check and reassemble the whole thing.

How to replace the rear license plate bulb on my hyundai i20

Finally last solution, you must replace the bulb on the backplate of your hyundai i20, but you are not able to open the cover from the outside of your automobile. In such a case, here is the method to operate this operation:

  • Unplug the battery from your hyundai i20
  • Locate the position of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
  • Once established, before removing the bulb holders, unplug the holders for less complicated access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your hyundai i20, test it and reassemble it, paying attention to the clips on the trunk liner

.
There you have it, you have discovered the main solutions for replacing license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to accomplish it following the explanation of this article. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your hyundai i20. If you wish to change other bulbs like the position light bulbs on your hyundai i20 or the low beam bulbs on hyundai i20, don’t be reluctant to read our articles which explain you the process to follow.

In the event that you have any additional questions about the hyundai i20, do not hesitate to consult our hyundai i20 category.