It doesn’t matter if it’s for your specific safety, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are always operational is really important. Indeed, bulbs are wearing auto parts that will undoubtedly burn out over time and therefore need to be swapped out. You’re almost certainly on this site because one of your parking lights is burnt out and you’re wondering how to change your Hyundai Bayon’s license plate bulb, we’ve made this content page to help you do it by yourself and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Hyundai Bayon.
How to swap the license plate bulb on your Hyundai Bayon throughout the outside
This tactic is the least difficult of the two, actually, for this one you will only need to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second section of this article to demonstrate the method.
So let’s start with changing the number plate bulb by going through the outside of your Hyundai Bayon. It doesn’t matter if it’s the front or the back of your automobile the method will be similar.
Here are a few simple actions to stick to to perform this service:
- With the engine off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this intent (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Hyundai Bayon
- Use your screwdriver or knife to remove the bulb from its place, in the event you are worried of damaging something, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the achievement of the operation.
.
How to replace the number plate bulb on your Hyundai Bayon without outside access
Second section of our content, replace this license plate bulb on your Hyundai Bayon without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Hyundai Bayon
To swap the one on the front plate, nothing could be much easier, you will have to position yourself under the automobile (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to put in too much pressure otherwise you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my Hyundai Bayon
Finally last possibility, you must swap the bulb on the backplate of your Hyundai Bayon, but you cannot really open the cover from the outside of your automobile. In such a case, here is the technique to conduct this operation:
- Unplug the battery from your Hyundai Bayon
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Hyundai Bayon, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main techniques for changing license plate bulbs on your car, bear in mind that on some models the technique may be a bit different but you should be able to do it following the explanation of this article. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Hyundai Bayon. If you need to change other bulbs like the position light bulbs on your Hyundai Bayon or the low beam bulbs on Hyundai Bayon, don’t be reluctant to consult our articles which explain you the operation to follow.
If you need more tutorials on the Hyundai Bayon, go to our Hyundai Bayon category.
