It doesn’t matter if it’s for your own safety, for roadworthiness testing or to avoid a fine, ensuring your headlamp bulbs are in every case effective is necessary. In reality, bulbs are wearing units that will predictably burn out after some time and consequently need to be changed. You’re almost certainly in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Honda Element’s license plate bulb, we’ve written this content to help you do it without any help and not have to go to your auto mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Honda Element.
How to swap the license plate bulb on your Honda Element through the outside
This solution is the fastest of the two, in reality, for this one you will just require to remove the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second part of this content page to clarify the way.
So let’s start with swapping the number plate bulb by going through the outside of your Honda Element. It doesn’t matter if it’s the front or the back of your vehicle the operation will be the same.
Here are a few simple actions to follow to perform this service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Honda Element
- Use your screwdriver or knife to eject the bulb from its location, in the event you are afraid of destroying something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to validate the successfulness of the task.
.
How to replace the number plate bulb on your Honda Element without outside access
Second part of our document, replace this license plate bulb on your Honda Element without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Honda Element
To swap the one on the front plate, nothing could be less difficult, you will have to position yourself under the vehicle (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to put in too much pressure or you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and swap it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my Honda Element
Finally last solution, you must swap the bulb on the backplate of your Honda Element, but you are not able to open the cover from the outside of your vehicle. In such a case, here is the tactic to do this operation:
- Disconnect the battery from your Honda Element
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Honda Element, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main techniques for swapping license plate bulbs on your car, take notice that on some models the technique may be a bit different but you should be able to realize it following the outline of this content. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Honda Element. If you desire to change other bulbs like the position light bulbs on your Honda Element or the low beam bulbs on Honda Element, don’t be reluctant to consult our articles which explain you the procedure to follow.
If you need more tutorials on the Honda Element, go to our Honda Element category.
