Regardless it’s for your personal security, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are in every case effective is extremely important. Indeed, bulbs are wearing parts that will inevitably burn out over time and as a result need to be swapped out. You’re probably on this site because one of your parking lights is burnt out and you’re worried about how to change your Honda E’s license plate bulb, we’ve written and published this content to help you do it all on your own and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Honda E.

change-license-plate-bulb-honda-e

How to swap the license plate bulb on your Honda E through the outside

This tactic is the most simple of the two, actually, for this one you will simply require to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second section of this document to show you the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Honda E. Regardless it’s the front or the back of your car the operation will be similar.
Here are a few simple actions to stick to to execute this service:

  • With the engine turned off, disconnect the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this goal (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Honda E
  • .

  • Use your screwdriver or knife to eject the bulb from its placement, in the event you are worried of breaking anything, you can also do it with your fingers.
  • Finally, position the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and check the light to validate the achievement of the operation.

How to change the number plate bulb on your Honda E without outside access

Second section of our item, swap this license plate bulb on your Honda E without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).

How to swap the front license plate bulb on my Honda E

To swap the one on the front plate, nothing could be easier, you will have to position yourself under the car (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Remove the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to apply too much pressure otherwise you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.

How to swap the rear license plate bulb on my Honda E

Finally last possibility, you must swap the bulb on the backplate of your Honda E, but you simply cannot open the cover from the outside of your car. In this instance, here is the solution to perform this task:

  • Disconnect the battery from your Honda E
  • Find the position of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
  • Once found, before removing the bulb holders, disconnect the holders for easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Honda E, check it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have found out the main solutions for swapping license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to realize it following the outline of this article content. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Honda E. If you want to change other bulbs like the position light bulbs on your Honda E or the low beam bulbs on Honda E, don’t hesitate to consult our content articles which describe you the operation to follow.

To get more tips on the Honda E, take a look at the Honda E category.