Whether it’s for your personal safety, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are always functioning is necessary. In fact, bulbs are wearing parts that will obviously burn out as time passes and as a consequence need to be replaced. You’re almost certainly on this website because one of your parking lights is burnt out and you’re wanting to know how to change your Ford S-max 2’s license plate bulb, we’ve written and published this article to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Ford S-max 2.
How to change the license plate bulb on your Ford S-max 2 throughout the outside
This option is the fastest of the two, actually, for this one you will just require to take out the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate a moment on in the second part of this content page to explain the approach.
So let’s begin with replacing the number plate bulb by going through the outside of your Ford S-max 2. Whether it’s the front or the back of your automobile the operation will be similar.
Here are a few simple steps to follow to conduct this routine service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this goal (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ford S-max 2
- Use your screwdriver or knife to remove the bulb from its location, if you are afraid of breaking a thing, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to confirm the achievement of the operation.
.
How to change the number plate bulb on your Ford S-max 2 without outside access
Second part of our document, change this license plate bulb on your Ford S-max 2 without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Ford S-max 2
To change the one on the front plate, nothing could be simpler, you will have to put yourself under the automobile (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take away the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to exert too much pressure otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Ford S-max 2
Finally last possibility, you must change the bulb on the backplate of your Ford S-max 2, but you are not able to open the cover from the outside of your automobile. In such a case, here is the tactic to accomplish this operation:
- Unplug the battery from your Ford S-max 2
- Locate the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Ford S-max 2, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main approaches for replacing license plate bulbs on your car, be aware that on some models the method may be a bit different but you should be able to accomplish it following the outline of this content. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Ford S-max 2. If you want to change other bulbs like the position light bulbs on your Ford S-max 2 or the low beam bulbs on Ford S-max 2, don’t be reluctant to browse our articles which describe you the procedure to follow.
If perhaps you have any further questions about the Ford S-max 2, do not hesitate to consult our Ford S-max 2 category.
