Whether it’s for your personal safety, for roadworthiness testing or to avoid a fine, making sure your headlamp bulbs are constantly operational is fundamental. In reality, bulbs are wearing units that will undoubtedly burn out in the future and as a result need to be changed. You’re likely on this site because one of your parking lights is burnt out and you’re wondering how to change your Ford Ranger’s license plate bulb, we’ve created this content to help you do it on your own and not have to go to your auto mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Ford Ranger.
How to change the license plate bulb on your Ford Ranger through the outside
This tactic is the simplest of the two, in truth, for this one you will only require to take off the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second section of this content to clarify the method.
So let’s begin with changing the number plate bulb by going through the outside of your Ford Ranger. Whether it’s the front or the back of your vehicle the process will be identical.
Here are a few simple steps to stick to to perform this service:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this goal (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ford Ranger
- Use your screwdriver or knife to remove the bulb from its location, if you are scared of damaging anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the achievement of the procedure.
.
How to replace the number plate bulb on your Ford Ranger without outside access
Second section of our document, replace this license plate bulb on your Ford Ranger without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Ford Ranger
To change the one on the front plate, nothing could be simpler, you will have to position yourself under the vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much force or you will break the plastic cover), and you will simply have to take off the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Ford Ranger
Finally last option, you must change the bulb on the backplate of your Ford Ranger, but you cannot really open the cover from the outside of your vehicle. In such a case, here is the method to execute this operation:
- Disconnect the battery from your Ford Ranger
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Ford Ranger, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main approaches for changing license plate bulbs on your car, take notice that on some models the method may be a bit different but you should be able to realize it following the outline of this document. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Ford Ranger. If you wish to change other bulbs like the position light bulbs on your Ford Ranger or the low beam bulbs on Ford Ranger, don’t be reluctant to browse our content articles which demonstrate you the operation to follow.
If you have any further questions about the Ford Ranger, do not hesitate to consult our Ford Ranger category.
