It doesn’t matter if it’s for your personal security, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are constantly operational is fundamental. In fact, bulbs are wearing units that will predictably burn out over time and therefore need to be replaced. You’re likely on this website because one of your parking lights is burnt out and you’re wondering how to change your Ford F 250’s license plate bulb, we’ve made this article content to help you do it all on your own and not have to go to your auto mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Ford F 250.
How to replace the license plate bulb on your Ford F 250 through the outside
This solution is the easiest of the two, in reality, for this one you will just need to remove the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second part of this content to describe the way.
So let’s start with replacing the number plate bulb by going through the outside of your Ford F 250. It doesn’t matter if it’s the front or the back of your car the method will be the same.
Here are a few simple actions to follow to carry out this service:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ford F 250
- Use your screwdriver or knife to eject the bulb from its location, in the event that you are scared of destroying anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to confirm the success of the operation.
.
How to replace the number plate bulb on your Ford F 250 without outside access
Second part of our content, replace this license plate bulb on your Ford F 250 without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Ford F 250
To replace the one on the front plate, nothing could be much easier, you will have to position yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to apply too much pressure otherwise you will break the plastic cover), and you will just have to remove the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Ford F 250
Finally last possibility, you must replace the bulb on the backplate of your Ford F 250, but you cannot open the cover from the outside of your car. In this case, here is the technique to perform this operation:
- Unplug the battery from your Ford F 250
- Locate the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Ford F 250, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main methods for replacing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to realize it following the outline of this document. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Ford F 250. If you need to change other bulbs like the position light bulbs on your Ford F 250 or the low beam bulbs on Ford F 250, don’t hesitate to read our articles which describe you the procedure to follow.
To find more tips on the Ford F 250, take a look at the Ford F 250 category.
