It doesn’t matter if it’s for your specific security, for roadworthiness testing or to avoid a fine, being certain your headlamp bulbs are constantly effective is really important. Indeed, bulbs are wearing units that will obviously burn out over the years and therefore need to be swapped out. You’re most likely in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Ford Expedition’s license plate bulb, we’ve written this document to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Ford Expedition.
How to change the license plate bulb on your Ford Expedition through the outside
This process is the simplest of the two, in reality, for this one you will only require to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second part of this article content to clarify the approach.
So let’s begin with changing the number plate bulb by going through the outside of your Ford Expedition. It doesn’t matter if it’s the front or the back of your motor vehicle the method will be the same.
Here are a few simple steps to stick to to carry out this maintenance:
- With the engine turned off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this purpose (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ford Expedition
- Use your screwdriver or knife to eject the bulb from its location, if you are afraid of destroying something, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to validate the successfulness of the task.
.
How to replace the number plate bulb on your Ford Expedition without outside access
Second part of our item, swap this license plate bulb on your Ford Expedition without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Ford Expedition
To change the one on the front plate, nothing could be less complicated, you will have to put yourself under the motor vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly kept by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Take out the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to exert too much force otherwise you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to change the rear license plate bulb on my Ford Expedition
Finally last solution, you must change the bulb on the backplate of your Ford Expedition, but you simply cannot open the cover from the outside of your motor vehicle. In such a case, here is the tactic to perform this operation:
- Unplug the battery from your Ford Expedition
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Ford Expedition, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main ways for changing license plate bulbs on your car, take notice that on some models the method may be a bit different but you should be able to realize it following the outline of this article content. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Ford Expedition. If you want to change other bulbs like the position light bulbs on your Ford Expedition or the low beam bulbs on Ford Expedition, don’t be reluctant to consult our articles which demonstrate you the operation to follow.
If you wish more tutorials on the Ford Expedition, go to our Ford Expedition category.
