Regardless whether it’s for your own personal security, for roadworthiness tests or to avoid a fine, ensuring your headlamp bulbs are in every case effective is really important. In fact, bulbs are wearing units that will predictably burn out in the future and as a result need to be swapped out. You’re almost certainly in this article because one of your parking lights is burnt out and you’re wondering how to change your Ford Escape’s license plate bulb, we’ve written and published this document to help you do it by yourself and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Ford Escape.
How to swap the license plate bulb on your Ford Escape coming from the outside
This tactic is the most simple of the two, actually, for this one you will just need to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will spend a moment on in the second part of this content page to demonstrate the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Ford Escape. Regardless whether it’s the front or the back of your motor vehicle the process will be identical.
Here are a few simple steps to follow to conduct this routine service:
- With the engine turned off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this intent (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ford Escape
- Use your screwdriver or knife to remove the bulb from its placement, in the event you are worried of destroying a thing, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to confirm the achievement of the operation.
.
How to replace the number plate bulb on your Ford Escape without outside access
Second part of our content page, replace this license plate bulb on your Ford Escape without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Ford Escape
To swap the one on the front plate, nothing could be much easier, you will have to position yourself under the motor vehicle (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take out the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to apply too much force or you will break the plastic cover), and you will just have to remove the burnt-out license plate bulb and swap it with the new , then test and reassemble the whole thing.
How to swap the rear license plate bulb on my Ford Escape
Finally last possibility, you must swap the bulb on the backplate of your Ford Escape, but you cannot open the cover from the outside of your motor vehicle. In this case, here is the process to execute this task:
- Unplug the battery from your Ford Escape
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Ford Escape, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main approaches for swapping license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to accomplish it following the explanation of this document. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Ford Escape. If you want to change other bulbs like the position light bulbs on your Ford Escape or the low beam bulbs on Ford Escape, don’t hesitate to consult our articles which demonstrate you the process to follow.
To discover more tips on the Ford Escape, take a look at the Ford Escape category.
