Regardless whether it’s for your personal safety, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are constantly functioning is very important. In fact, bulbs are wearing parts that will inevitably burn out after awhile and consequently need to be changed. You’re almost certainly in this article because one of your parking lights is burnt out and you’re questioning how to change your Ford E Series’s license plate bulb, we’ve made this article content to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Ford E Series.
How to replace the license plate bulb on your Ford E Series coming from the outside
This method is the fastest of the two, in truth, for this one you will simply require to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second section of this article content to explain the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Ford E Series. Regardless whether it’s the front or the back of your car the method will be similar.
Here are a few simple guidelines to follow to carry out this service:
- With the engine off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this goal (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ford E Series
- Use your screwdriver or knife to eject the bulb from its placement, in the event you are afraid of destroying a thing, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to validate the success of the procedure.
.
How to replace the number plate bulb on your Ford E Series without outside access
Second section of our article, swap this license plate bulb on your Ford E Series without external access. Generally you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Ford E Series
To replace the one on the front plate, nothing could be less difficult, you will have to position yourself under the car (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take away the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to exert too much pressure or you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to replace the rear license plate bulb on my Ford E Series
Finally last solution, you must replace the bulb on the backplate of your Ford E Series, but you simply cannot open the cover from the outside of your car. In this case, here is the process to perform this task:
- Disconnect the battery from your Ford E Series
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Ford E Series, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main tactics for replacing license plate bulbs on your car, bear in mind that on some models the technique may be a bit different but you should be able to accomplish it following the explanation of this content. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Ford E Series. If you need to change other bulbs like the position light bulbs on your Ford E Series or the low beam bulbs on Ford E Series, don’t be reluctant to read our articles which describe you the operation to follow.
To get more tips on the Ford E Series, take a look at the Ford E Series category.
