Whether it’s for your personal security, for roadworthiness tests or to avoid a fine, ensuring your headlamp bulbs are constantly operational is fundamental. In fact, bulbs are wearing units that will surely burn out after some time and as a result need to be swapped out. You’re likely on the website because one of your parking lights is burnt out and you’re questioning how to change your Ford C-max 2’s license plate bulb, we’ve made this document to help you do it on your own and not have to go to your mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Ford C-max 2.
How to change the license plate bulb on your Ford C-max 2 through the outside
This technique is the quickest of the two, in reality, for this one you will simply have to take away the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate a moment on in the second part of this article to describe the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Ford C-max 2. Whether it’s the front or the back of your vehicle the process will be the same.
Here are a few simple actions to follow to carry out this service:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ford C-max 2
- Use your screwdriver or knife to remove the bulb from its spot, in the event that you are scared of breaking anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the achievement of the operation.
.
How to change the number plate bulb on your Ford C-max 2 without outside access
Second part of our content, change this license plate bulb on your Ford C-max 2 without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Ford C-max 2
To change the one on the front plate, nothing could be simpler, you will have to position yourself under the vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much force otherwise you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Ford C-max 2
Finally last possibility, you must change the bulb on the backplate of your Ford C-max 2, but you are not able to open the cover from the outside of your vehicle. In this case, here is the method to do this operation:
- Unplug the battery from your Ford C-max 2
- Locate the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Ford C-max 2, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main techniques for swapping license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to do it following the outline of this content. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Ford C-max 2. If you need to change other bulbs like the position light bulbs on your Ford C-max 2 or the low beam bulbs on Ford C-max 2, don’t hesitate to read our articles which explain you the process to follow.
Whenever you have any additional questions about the Ford C-max 2, do not hesitate to consult our Ford C-max 2 category.
