It doesn’t matter if it’s for your specific security, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are constantly functional is really important. In fact, bulbs are wearing parts that will predictably burn out with time and consequently need to be replaced. You’re most certainly on this website because one of your parking lights is burnt out and you’re wanting to know how to change your Fiat Bravo 2’s license plate bulb, we’ve written and published this article content to help you do it without any help and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Fiat Bravo 2.
How to swap the license plate bulb on your Fiat Bravo 2 throughout the outside
This method is the easiest of the two, actually, for this one you will just have to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will spend a moment on in the second section of this content page to demonstrate the way.
So let’s begin with replacing the number plate bulb by going through the outside of your Fiat Bravo 2. It doesn’t matter if it’s the front or the back of your vehicle the operation will be similar.
Here are a few simple actions to stick to to conduct this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Fiat Bravo 2
- Use your screwdriver or knife to remove the bulb from its spot, in the event you are afraid of destroying a thing, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to confirm the successfulness of the procedure.
.
How to change the number plate bulb on your Fiat Bravo 2 without outside access
Second section of our article, replace this license plate bulb on your Fiat Bravo 2 without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Fiat Bravo 2
To swap the one on the front plate, nothing could be easier, you will have to position yourself under the vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take out the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to put in too much pressure or you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and swap it with the new , then test and reassemble the whole thing.
How to swap the rear license plate bulb on my Fiat Bravo 2
Finally last solution, you must swap the bulb on the backplate of your Fiat Bravo 2, but you cannot open the cover from the outside of your vehicle. In this case, here is the technique to operate this operation:
- Disconnect the battery from your Fiat Bravo 2
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Fiat Bravo 2, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main approaches for replacing license plate bulbs on your car, take note that on some models the methodology may be a bit different but you should be able to accomplish it following the explanation of this article. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Fiat Bravo 2. If you need to change other bulbs like the position light bulbs on your Fiat Bravo 2 or the low beam bulbs on Fiat Bravo 2, don’t be reluctant to consult our articles which explain you the operation to follow.
In the event that you have any additional questions about the Fiat Bravo 2, do not hesitate to consult our Fiat Bravo 2 category.
