It doesn’t matter if it’s for your own safety, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are constantly operational is very important. In reality, bulbs are wearing units that will inevitably burn out over the years and therefore need to be replaced. You’re likely on the website because one of your parking lights is burnt out and you’re wanting to know how to change your Fiat 500’s license plate bulb, we’ve made this article to help you do it by yourself and not have to go to your mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Fiat 500.

change-license-plate-bulb-fiat-500

How to replace the license plate bulb on your Fiat 500 coming from the outside

This solution is the quickest of the two, in truth, for this one you will simply need to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second section of this article content to clarify the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Fiat 500. It doesn’t matter if it’s the front or the back of your car the technique will be identical.
Here are a few simple steps to stick to to conduct this maintenance:

  • With the engine off, disconnect the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Fiat 500
  • .

  • Use your screwdriver or knife to remove the bulb from its placement, if you are afraid of destroying something, you can also do it with your fingers.
  • Finally, position the new license plate light bulb
  • Last step, before reassembling, reconnect your battery and verify the light to confirm the achievement of the task.

How to replace the number plate bulb on your Fiat 500 without outside access

Second section of our content page, replace this license plate bulb on your Fiat 500 without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).

How to replace the front license plate bulb on my Fiat 500

To replace the one on the front plate, nothing could be less complicated, you will have to position yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at the same time, then once you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to exert too much pressure otherwise you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.

How to replace the rear license plate bulb on my Fiat 500

Finally last solution, you must replace the bulb on the backplate of your Fiat 500, but you cannot really open the cover from the outside of your car. In such a case, here is the method to conduct this task:

  • Unplug the battery from your Fiat 500
  • Locate the location of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
  • Once established, before removing the bulb holders, disconnect the holders for less difficult access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Change the burnt-out license plate bulb on your Fiat 500, verify it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have discovered the main solutions for replacing license plate bulbs on your car, bear in mind that on some models the technique may be a bit different but you should be able to do it following the explanation of this content. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Fiat 500. If you need to change other bulbs like the position light bulbs on your Fiat 500 or the low beam bulbs on Fiat 500, don’t be reluctant to read our content articles which explain you the procedure to follow.

If you want more guides on the Fiat 500, go to our Fiat 500 category.